- 您现在的位置：买卖IC网 > Sheet目录969 > CDB4365 (Cirrus Logic Inc)EVALUATION BOARD FOR CS4365
CS4365
4.7
ATAPI Specification
The CS4365 implements the channel-mixing functions of the ATAPI CD-ROM specification. The
ATAPI functions are applied per A-B pair. Refer to Table 9 on page 42 and Figure 17 for additional informa-
tion.
SDINx
Left Channel
Audio Data
Right Channel
Audio Data
Σ
A Channel
Volume
Control
B Channel
Volume
Control
Σ
MUTE
MUTE
Aout Ax
AoutBx
Figure 17. ATAPI Block Diagram (x = channel pair 1, 2, or 3)
4.8
26
Direct Stream Digital (DSD) Mode
In Software Mode, the DSD/PCM bits (Reg. 02h) are used to configure the device for DSD Mode. The
DSD_DIF bits (Reg 04h) then control the expected DSD rate and MCLK ratio.
The DIR_DSD bit (Reg 04h) selects between two proprietary methods for DSD-to-analog conversion. The
first method uses a decimation-free DSD processing technique which allows for features such as matched
PCM-level output, DSD volume control, and 50kHz on-chip filter. The second method sends the DSD data
directly to the on-chip switched-capacitor filter for conversion (without the above-mentioned features).
The DSD_PM_EN bit (Reg. 04h) selects Phase Modulation (data plus data inverted) as the style of data
input. In this mode, the DSD_PM_mode bit selects whether a 128Fs or 64x clock is used for phase modu-
lated 64x data (see Figure 18 ). Use of Phase Modulation Mode may not directly affect the performance of
the CS4365, but may lower the sensitivity to board-level routing of the DSD data signals.
The CS4365 can detect errors in the DSD data which does not comply with the SACD specification. The
STATIC_DSD and INVALID_DSD bits (Reg. 04h) allow the CS4365 to alter the incoming invalid DSD data.
Depending on the error, the data may either be attenuated or replaced with a muted DSD signal (the
MUTEC pins would be set according to the DAMUTE bit (Reg. 08h)).
More information for any of these register bits can be found in Section 7. “Filter Plots” on page 45 .
The DSD input structure and analog outputs are designed to handle a nominal 0 dB-SACD (50% modulation
index) at full rated performance. Signals of +3 dB-SACD may be applied for brief periods of time, however;
performance at these levels is not guaranteed. If sustained +3 dB-SACD levels are required, the digital vol-
ume control should be set to -3.0 dB. This same volume control register affects PCM output levels. There
is no need to change the volume control setting between PCM and DSD in order to have the 0dB output
levels match (both 0 dBFS and 0 dB-SACD will output at -3 dB in this case).
DS670F2
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
CDB4385
BOARD EVAL FOR CS4385 DAC
CDB43L22
BOARD EVAL FOR CS43L22
CDB5340
BOARD EVAL FOR CS5340 STEREO ADC
CDB5343
BOARD EVAL FOR CS5343 STEREO ADC
CDB5451A
EVAL BOARD CS5451A 6CH ADC
CDB5524
EVAL BOARD FOR CS5524 ADC
CDB5581
BOARD EVAL FOR CS5581 ADC
CDK5571
CDB5571 W/CAPTURE PLUS 2 SYSTEM
相关代理商/技术参数
CDB4382
制造商:Cirrus Logic 功能描述:Tools Development kit Kit Con
CDB4382A
功能描述:音频 IC 开发工具 Eval Bd 114dB 192kHz 8-Ch DAC w/DSD
RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V
CDB4383
制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:114 dB, 192 kHz 8-Channel D/A Converter
CDB4384
功能描述:音频 IC 开发工具 Eval Bd 8-Ch DAC w/DSD
RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V
CDB4385
功能描述:音频 IC 开发工具 Eval Bd 8-Ch DAC w/DSD RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V
CDB4390
制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:24-Bit, Stereo D/A Converter for Digital Audio
CDB4391
制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:24-Bit, 192 kHz Stereo DAC with Volume Control
CDB4391A
功能描述:音频 IC 开发工具 Eval Bd CS4391A
RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V